Flipper Zero BLE tools

A suite of BLE, sub-GHz and power tools for the Flipper Zero. The BLE apps share one central/GATT layer (libble/).

Bluetooth (need the build.sh firmware)

• BT Inspector — BLE scanner and GATT explorer, in the spirit of BTInspector for iOS: discover devices, decode everything they broadcast, then connect and inspect/read/write/subscribe, and log it all.
• BLE HID Host — connect a Bluetooth keyboard or mouse and watch its input reports decoded live.
• BLE Sensor Dashboard — connect a sensor and watch its known-service readings (battery, heart rate, temperature, humidity, pressure, ...) decoded and updating live.
• BLE Tracker Detector — passively flag nearby item trackers (Apple Find My / AirTag, Tile, Samsung SmartTag) with a "following you" warning.
• BLE GATT Fuzzer — enumerate a peripheral's whole GATT database, read every readable value, and fuzz writable characteristics with boundary payloads, logging every response. For authorised testing of devices you own.
• BLE Beacon Toolkit — broadcast an iBeacon or a raw advertising payload with a chosen random MAC.
• BLE GATT Server — advertise the Flipper as a connectable serial GATT peripheral and echo whatever a central writes.

Sub-GHz (need the region unlock, on by default)

• Sub-GHz Scanner — sweep RSSI across the full CC1101 range and log active frequencies.
• Sub-GHz Spectrum — live spectrum bar graph and waterfall over a tunable centre/span window.

Tools

• Battery Health — live fuel-gauge readings (voltage, current, temperature, capacity, health, wear) with a voltage graph. Read-only.

Read this first. These apps do not run on stock Flipper firmware. The Flipper's radio coprocessor ships with ST's "BLE Light" stack (advertise-only: it cannot scan or connect), and the sub-GHz region check blocks transmit off-region. They are delivered as a custom firmware build that swaps in ST's full BLE stack, exports the BLE command API to apps, and unlocks the sub-GHz region; the apps themselves are ordinary .fap files. build.sh does all of this. See Why a custom firmware build. Battery Health is the only one that would also run on stock firmware.

Features

• Live scan list. Every BLE advertiser in range, sorted by RSSI, refreshed every 300 ms as you move around. Shows name (or "(no name)"), RSSI in dBm with signal bars, address and vendor. Devices unseen for 60 s drop off.
• Device page. Address and address type, current/best RSSI and packet count, advertising type (connectable or not), flags, advertised service UUIDs (16/32/128-bit, named when known), service data, Tx power, appearance, manufacturer data and raw advertisement / scan-response bytes. Updates live.
• Identification. Manufacturer IDs map to vendor names. Decoders for:
  • Apple Continuity: iBeacon (UUID/major/minor/Tx), Proximity Pairing with AirPods/Beats model name and left / right / case battery and charging state, Nearby Info (device activity), Nearby Action, Find My, AirDrop, Handoff, AirPlay, tethering.
  • Microsoft Connected Devices beacon: device type (Windows desktop/laptop, Xbox, Surface Hub, Android, iPhone, ...).
  • Google Fast Pair model ID, Eddystone UID/URL/TLM (URL decoded), COVID Exposure Notification.
• Connect and interrogate. OK on a connectable device connects (MTU is negotiated), discovers all primary services, then characteristics with their properties (Read, Write, write-without-response, Notify, Indicate, Broadcast).
• Read device info (first item in the service list): reads every readable characteristic of the Generic Access, Device Information and Battery services in one go: device name, appearance, model number, serial number, firmware / hardware / software revision, manufacturer name, PnP ID, battery level.
• Characteristic page. Read any characteristic, including custom 128-bit ones. Values are shown as hex plus decoded forms: printable string, u8/i8, u16, u32, and SIG-specific formats (battery %, appearance, preferred connection parameters, PnP ID, heart rate, temperature, humidity, pressure, Tx power, date/time). Long values are fetched with read-long.
• Write a value back as text, hex bytes or a number (little-endian, sized to the current value or the magnitude). Uses write-with-response when the characteristic supports it, otherwise write-without-response. A readable characteristic is re-read after a write.
• Subscribe to notifications / indications (the CCCD is located automatically). Incoming values update the page and the history.
• Value history. Each value seen for the open characteristic (reads and notifications) is kept with a timestamp, newest first.
• Session log. Every event is written with a date/time stamp to SD:/apps_data/bt_inspector/bti_YYYYMMDD_HHMMSS.log: devices found (and renamed), connects, services, characteristics, reads, writes, notifications, errors. Copy it off the SD card (or via qFlipper) for analysis.

Building and installing

Requirements: Linux or macOS with git, python3 and a few GB of disk. The firmware build system downloads its own ARM toolchain.

./build.sh          # clone firmware 1.4.3, export the BLE API, build firmware + .fap
./build.sh flash    # same, then flash over USB (Flipper connected, qFlipper closed)
./build.sh fap      # rebuild only the .fap after editing the app

Options via environment variables: FW_TAG (firmware tag, default 1.4.3), FW_DIR (where to clone), JOBS (parallel compile jobs, default 4), BLE_API (which ST API to export, see below).

The result is a standard update package in flipperzero-firmware/dist/f7-C/f7-update-local/. It contains the firmware, the full radio stack, and the app as apps/Bluetooth/bt_inspector.fap in its resources. To install without USB flashing, copy that folder to the SD card (for example SD:/update/) and open it in the Flipper's file browser. Installing an official firmware later restores the light stack the same way.

The .fap alone is at flipperzero-firmware/build/f7-firmware-C/.extapps/; after the firmware is installed once, app updates are just a file copy to SD:/apps/Bluetooth/. It only loads on this firmware (API version 87.2 with the exported symbols); the stock loader rejects it with an API mismatch.

To build the app with ufbt instead of the firmware tree, point ufbt at the SDK the build produces:

ufbt update --local=flipperzero-firmware/dist/f7-C/flipper-z-f7-sdk-local.zip
cd bt_inspector && ufbt        # -> dist/bt_inspector.fap ; `ufbt launch` installs it

The first build takes 5-15 minutes; later builds are incremental.

Using the app

BT Inspector appears in the Flipper's main menu. While it runs, the Flipper's own BLE advertising is stopped (and any phone connection dropped); it is restored on exit.

Screen	Up / Down	OK	Left	Right	Back
Scan list	select device	device page			exit app
Device page	scroll	Connect (if connectable)			scan list
Services	select	open service / read device info			disconnect, device page
Characteristics	select	open characteristic (auto-read)			services
Characteristic	scroll	Read	Notify / Unsub	Write	characteristics
Write menu	select	Text / Hex bytes / Number			characteristic

Status messages ("Read OK (5 B)", "Write failed: Write not permitted", "Notifications on", ...) appear on the characteristic page.

On stock firmware the app opens with an explanation instead of scanning.

Log format

One event per line:

[2026-09-11 09:12:03] START stack=full advertising_was=1
[2026-09-11 09:12:04] DEVICE 5C:F3:70:9A:11:20 ADV_IND rssi=-58 name="Living Room" vendor=Apple adv=02 01 1A 0B FF 4C 00 ...
[2026-09-11 09:12:20] CONNECTING Living Room
[2026-09-11 09:12:21] CONNECTED Living Room mtu=247
[2026-09-11 09:12:21] SERVICE 180A Device Information handles 0x0010-0x001C
[2026-09-11 09:12:25] CHAR 2A26 handle 0x0016 props 0x02
[2026-09-11 09:12:26] READ 0x0016 = 31 2E 32 2E 30
[2026-09-11 09:12:40] WRITE 0x0021 = 01
[2026-09-11 09:12:41] NOTIFY 0x0024 = 64
[2026-09-11 09:13:00] DISCONNECT

A DEVICE line is written when a device is first seen and again when its name changes. INFO lines come from "Read device info".

Why a custom firmware build

Three facts about the Flipper Zero drive the design:

1. The STM32WB55's second core runs a prebuilt ST BLE stack. Flipper ships stm32wb5x_BLE_Stack_light_fw.bin (peripheral + broadcaster only). ST's stm32wb5x_BLE_Stack_full_fw.bin adds observer and central roles. The firmware build system already supports it (COPRO_STACK_TYPE=ble_full) and the firmware recognises it at runtime (FuriHalBtStackFull).

2. External .fap apps can only call functions listed in the firmware's API table. The ST aci_* / hci_* command functions are not in it, so a stock .fap cannot start a scan or a connection. build.sh adds ST's command headers to the SDK (lib/stm32wb.scons), adds extern "C" guards to them (the API table is C++), lets fbt regenerate api_symbols.csv, and enables the selected functions. The API minor version becomes 87.2.

3. Every exported function is kept in the firmware image, so BLE_API trades generality for flash. The full stack loads at 0x080CE000 (light: 0x080D7000); the space between the firmware and the stack is the Flipper's internal storage:

   BLE_API	exported	firmware	pages left, full stack	pages left, extended stack
   min (app's own 15 imports)	15	770 KB	18	9
   hci,gatt (default)	127	779 KB	15	6
   all	211	~788 KB	13	4
   stock light-stack firmware	0	768 KB	27	n/a

   Any comma list of hci,gap,gatt,hal,l2cap works. extended refers to stm32wb5x_BLE_Stack_full_extended_fw.bin (BLE 5 extended advertising, Coded PHY), which loads at 0x080C5000; it is not selected by this script.

Extra firmware APIs exported to apps

Beyond the ST BLE commands, build.sh enables a set of firmware functions that stock firmware keeps internal, so any .fap on this firmware can use them. The set is a list of name patterns in build.sh (EXPORT_ENABLE); each enabled symbol costs one API-table entry. Only symbols named in EXPORT_ENABLE (plus the selected ST BLE commands) are exported; headers added for their types do not drag in every function they declare.

• BLE peripheral internals (gap_*, safe ble_glue_*, furi_hal_bt_init): drive GAP directly, run a custom GATT server, change the advertised name and the extra-beacon config, read connection state and radio-stack status, without going through the firmware's serial profile. The coprocessor firmware-update calls (ble_glue_fus_stack_delete/install) are deliberately left disabled, since they can erase the radio stack.
• Power / battery internals: the gas-gauge readings (voltage, current, temperature, remaining/full/design capacity, health, charge state) are already exported by stock firmware. This build also enables furi_hal_power_insomnia_level; furi_hal_power_init stays disabled.
• Flash + option-byte internals (furi_hal_flash_*): flash geometry, free-page info, and raw program / erase / dword-write / option-byte access. An app can read and modify internal flash directly. This can brick the device or wipe storage. Enabled here for research; build with EXPORT_FLASH=0 ./build.sh to leave these disabled.
• RPC + loader internals: the public rpc_* and loader_* APIs (RPC session open/feed/close, app data exchange, launching and enqueuing apps, lock/unlock, showing the app menu) are already exported by stock firmware and are the supported way to script the Flipper from a host or launch other apps. This build also adds the internal loader headers (loader_i.h, loader_menu.h, loader_queue.h, loader_applications.h) so apps can use the internal Loader types. The internal helper functions stay unexported: they are not in the firmware's API-table link, so exporting them would break the firmware build; only the public API is callable. rpc_i.h is not added because it depends on the protobuf headers, which are not in the SDK.

build.sh also widens the GAP roles the firmware initialises (GAP_PERIPHERAL_ROLE | GAP_CENTRAL_ROLE | GAP_OBSERVER_ROLE) in targets/f7/ble_glue/gap.c. The app itself uses HCI-level scan and connect commands, so this is belt-and-braces.

How it works

bt_inspector.c   UI (ViewDispatcher: scan list, text page, menus, inputs),
                 worker thread for blocking BLE operations, session log
ble_central.c    scan / connect / GATT client on top of the ST stack.
                 Registers a handler with the firmware's BLE event dispatcher,
                 acknowledges its own events (advertising reports, our
                 connection's events) so the firmware's peripheral GAP never
                 sees them, and turns async ATT events into synchronous calls
ble_names.c      vendor / UUID / appearance tables and value decoders

The app registers for BLE events, stops the Flipper's own advertising, then issues hci_le_set_scan_*, hci_le_create_connection and aci_gatt_* commands directly. Connection-complete events are distinguished from the firmware's peripheral connections by the role field. Advertising reports are parsed from the raw HCI payload (the ST header's Advertising_Report_t is not a wire overlay).

Sub-GHz region unlock (research)

build.sh also patches the firmware's sub-GHz region gate so transmit is allowed on any frequency the CC1101 can tune, regardless of the device's provisioned region: furi_hal_region_is_frequency_allowed and furi_hal_region_is_provisioned are forced true. This is what most "unlocked" Flipper firmwares do. The CC1101 PLL bands (about 300-348, 387-464 and 779-928 MHz) remain, because they are a hardware limit, not a regulatory one.

Transmitting outside the frequencies and power levels allocated to you may be illegal in your country. This is provided for research and authorised testing only; you are responsible for operating within the law. Build with SUBGHZ_UNLOCK=0 ./build.sh to leave the region limits in place.

Limitations

Shared / hardware

• BLE only. The STM32WB55 has no Bluetooth Classic (BR/EDR), so classic devices cannot be seen or connected from any Flipper.
• No pairing or bonding as central. Neither app pairs, so anything gated behind an encrypted link is out of reach: encrypted characteristics report "Insufficient auth" / "Insufficient encryption", and keyboards that only send reports after bonding stay silent.
• At most two concurrent links (the firmware's BLE config), and while either app runs the Flipper's own advertising is stopped and any phone link dropped, then restored on exit.
• Built and checked against firmware 1.4.3 as .fap apps; on-device behaviour needs a Flipper running the firmware from build.sh (full stack + exported API). The apps will not load on stock firmware (missing exported symbols).

BT Inspector

• Apple battery levels come from what AirPods/Beats broadcast. Battery of iPhones/Macs is only exposed to paired Apple devices.
• Vendor, UUID and Apple model tables are curated subsets; unknown IDs are shown as hex. Apple Continuity layouts are community-documented and may drift.
• Value history is kept for the open characteristic; the log file has all of it.
• iOS-only BTInspector features (Shortcuts, Live Activities, background scanning mapped by location) have no Flipper equivalent.

BLE HID Host

• Report-mode devices are decoded heuristically (8+ byte reports as keyboard, shorter as mouse) rather than by parsing the Report Map; unusual layouts (consumer-control keys, multi-touch, gamepads) may decode oddly or not at all.
• Keyboard decoding covers the common USB HID usage page; media/consumer keys and vendor usages show as raw [XX]. No key-repeat or text reconstruction, just the reports as they arrive.
• Only input reports are shown; output reports (LEDs) and feature reports are not driven.

Exported firmware APIs (unlocks)

• Every exported function stays in the firmware image, so larger BLE_API settings and the extra exports cost flash and shrink internal storage (see the table above). EXPORT_FLASH=0 and SUBGHZ_UNLOCK=0 opt out.
• Flash / option-byte access is raw and unguarded: a misbehaving app can wipe storage or brick the device. Nothing in these apps uses it; it is exposed for other apps built against this SDK.
• RPC/loader internals expose only the internal types; the internal helper functions are not exported (they are not in the firmware API-table link). The public RPC and loader APIs remain the supported surface.
• Sub-GHz unlock removes the region check only. The CC1101 PLL bands (~300-348 / 387-464 / 779-928 MHz) still bound what the radio can tune, and transmitting outside your local allocation may be illegal. Research and authorised testing only; you are responsible for legal operation.
• The exported ST BLE command API and these unlocks are compile-verified, not exercised on hardware.

Troubleshooting

• "Radio stack has no scanning" on launch: the light stack is installed. Install the package produced by build.sh, which includes radio.bin with the full stack.
• Build killed / out of memory: JOBS=2 ./build.sh.
• App refuses to load ("API mismatch" / unresolved symbol): the firmware on the device is not the one from build.sh, or it was built with a smaller BLE_API than the app needs. Reinstall the update package.
• "API version is still WIP" during a build: fbt found symbols the script did not classify. Open targets/f7/api_symbols.csv, replace the remaining ? marks with + or -, rerun.
• Connect failed: Timeout: the device may not be connectable (see the advertising type on the device page), or it is out of range. Random-address devices that rotate their address may need re-selecting from the list.

The BLE HID Host app

Select a device from the scan list; the app connects, finds the HID service (0x1812), sets the protocol mode (boot when the device offers boot reports, otherwise report mode), and subscribes to its input-report characteristics. Keyboard reports are decoded to modifier + key names, mouse reports to button state and dx/dy/wheel. Events scroll on screen (Up/Down to review history) and are logged to SD:/apps_data/ble_hid_host/hid_*.log with the raw bytes. Back disconnects and returns to scanning.

It cannot pair, so keyboards that require an encrypted link before sending reports will connect but stay silent; open ones and most mice work.

Layout

libble/            shared BLE central / GATT client + name & value decoders
bt_inspector/      BT Inspector app (application.fam, icon.png, bt_inspector.c)
ble_hid_host/      BLE HID Host app (HID-over-GATT setup + report decoding)
build.sh           firmware build / flash script (stages libble into each app)
flipperzero-firmware/   created by build.sh (git-ignored)

build.sh copies libble/*.{c,h} into each app directory at build time, so both apps compile against one source of truth. Add an app by dropping its directory next to these and adding its name to APPS=(...) in build.sh.